TFR8-S modtager, 8 kanaler

TFR8-S modtager, 8 kanaler

330,00 DKK

TFR8-S kopi modtager til Futaba FASST 2,4 GHz, 8 kanaler.
Model/Varenr.: 03022008
DETTE ER IKKE EN ORIGINAL FUTABA MODTAGER, MEN PASSER SAMMEN MED FUTABA FASST.

Modtager der passer sammen med Futata FASST 2,4 GHz anlæg (TM7, TM8, TM10, TM14, etc).

Kanaler: 8, kan kobles sammen så der opnås 14 kanaler
Størrelse: 15x30x54 mm
Vægt: 14,9 gram
Rækkevidde: Fuld rækkevidde
Latency: Kan omstilles mellem 7ms (HS) og 14ms (FS)
Opløsning:
Failsafe: Ja
Spænding: 3,5V til 10V

Details:
1.TF Receivers
Please note that there are many differences between other brand and FrSky, especially in the binding procedure and failsafe setting. Read the instruction manual carefully and set up devices as described below.

1.1 Compatibility:
FASST 2.4G Air Systems (7CH Mode/Multi Mode): 6EX, 7C, TM-7, TM-8, T8FG, T10C, TM-10, T10CG, T12Z, T12FG, TM-14, T14MZ, etc.
FASST 2.4G Surface Systems (C1 Mode): 3PK, 4PK, etc.

1.2 Specifications:
Number of Channels: 8
Operating Voltage Range: 3.5V~10V
Operating Temperature Range: -10℃~60℃
Dimension: 54*30*15mm
Weight: 14.9g
Latency: 14ms (FS)
7ms (HS)

1.3 Features:
1) Compatible with Futaba FASST 2.4GHz systems, including ground systems (such as 3PK, 4PK)
2) Parallel with TFR8/TFR8-S to become a 14 channel FASST compatible receiver
3) Improve capability of anti-interference
4) Firmware upgradable

2. Setup
2.1 Bind procedure:
Turn on the transmitter, connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is off and GREEN LED is solid, the binding process is completed and the receiver is operating normally.

2.2 Setting failsafe:

TF series receivers support failsafe function for all channels. Follow the steps below to set failsafe:
1) Bind the receiver first, and disable failsafe on the transmitter side;
2) Set all transmitter controls to the desired failsafe position;
3) Press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, indicating the failsafe is set up successfully.
If you do not need the failsafe function any more, just re-bind the receiver to set default failsafe mode.

Warning: Some transmitter manufacturers use a failsafe method that can interfere with that used by FrSky. Be sure to disable any transmitter failsafe settings before setting FrSky failsafe positions. Unusual jitter may result otherwise
.
2.3 LED status:
RED LED GREEN LED Mode
Off On Normal mode
On On Waiting to be bound
Flashing On Signal lost
On Flashing twice Set failsafe
Flashing slowly On FS mode
Flashing fast On HS mode

3. How to switch between two PPM modes
Turn the transmitter off, connect the battery to the receiver, press the F/S button of receiver for 6 seconds and then release. The red LED will flash fast in HS Mode and slowly in FS Mode.Repeat this to alternate modes.

Warning: HS Mode is only applied for high-speed digital servos. Other servos should select FS Mode, otherwise servos will get heat or even burn out.
Titel Type Størrelse Download
TFR8-S-Manual.pdf PDF 663.13KB Download

Kunder der har købt dette produkt har også købt